华擎Z77主板，板载故障码d6，蜂鸣器短鸣4次。是什么问题

1. 华擎Z77主板，板载故障码d6，蜂鸣器短鸣4次。是什么问题

如果电脑有故障，它可通过摩斯密码告诉，电脑的毛病出在哪里。
PC喇叭的开机警报判断问题 
1声短鸣：内存刷新失败。 
2声短鸣：内存ECC校验错误。 
3声短鸣：系统基本内存(第1个64KB容量)自检失败。 
4声短鸣：系统时钟出错。 
5声短鸣：CPU出错。 
6声短鸣：键盘控制器错误。 
7声短鸣：系统实模式错误，不能进入保护模式。 
8声短鸣：显示内存错误(如显示内存损坏)。 
9声短鸣：主板FlashROM或EPROM检验错误(例如BIOS被CIH病毒破坏)。 
1长3声短鸣：内存错误(例如内存芯片损坏)。 
1长8声短鸣：显示系统测试错误(如显示器数据线或显示卡接触不良)。 
Award BIOS 
1声短鸣：系统正常启动。 
2声短鸣：常规错误。应进入CMOSSETUP，重新设置不正确的选项。 
1声长鸣1短声鸣：内存或主板出错。 
1声长鸣2短声鸣：显示器或显示卡错误。 
1声长鸣3声短鸣：键盘控制器错误。 
1声长鸣9声短鸣：主板FlashRAM或EPROM错误(例如BIOS被CIH破坏)。 
不间断长“嘟”声：内存未插好或有芯片损坏。 
不停响声：显示器未与显示卡连接。 
重复短“嘟”声：电源有故障。 
无“嘟”声同时无显示：主板电源未接通，或电源损坏。

2. 华擎z97极限玩家6故障代码

华擎z97极限玩家6故障代码是这样：启动时五短声报警，显示器无显示，主板显示d6故障，需重启两三次才能正常启动，请问是主板供电不足还是显卡故障。

3. 华擎Z77极限玩家4主板故障代码大全

其实这个官网上下载说明书就有的。下面附上。
Status Code Description
0x00 Not used
0x01 Power on. Reset type detection (soft/hard)
0x02 AP initialization before microcode loading
0x03 North Bridge initialization before microcode loading
0x04 South Bridge initialization before microcode loading
0x05 OEM initialization before microcode loading
0x06 Microcode loading
0x07 AP initialization after microcode loading
0x08 North Bridge initialization after microcode loading
0x09 South Bridge initialization after microcode loading
0x0A OEM initialization after microcode loading
0x0B Cache initialization
0x0C – 0x0D Reserved for future AMI SEC error codes
0x0E Microcode not found
0x0F Microcode not loaded
0x10 PEI Core is started
0x11 Pre-memory CPU initialization is started
0x12 Pre-memory CPU initialization (CPU module specific)
0x13 Pre-memory CPU initialization (CPU module specific)
0x14 Pre-memory CPU initialization (CPU module specific)
0x15 Pre-memory North Bridge initialization is started
0x16 Pre-Memory North Bridge initialization (North Bridge module specific)
0x17 Pre-Memory North Bridge initialization (North Bridge module specific)
0x18 Pre-Memory North Bridge initialization (North Bridge module specific)
0x19 Pre-memory South Bridge initialization is started
0x1A Pre-memory South Bridge initialization (South Bridge module specific)
0x1B Pre-memory South Bridge initialization (South Bridge module specific)
0x1C Pre-memory South Bridge initialization (South Bridge module specific)
0x1D – 0x2A OEM pre-memory initialization codes
0x2B Memory initialization. Serial Presence Detect (SPD) data reading
0x2C Memory initialization. Memory presence detection
0x2D Memory initialization. Programming memory timing information
0x2E Memory initialization. Configuring memory
0x2F Memory initialization (other)
0x30 Reserved for ASL
0x31 Memory Installed
0x32 CPU post-memory initialization is started
0x33 CPU post-memory initialization. Cache initialization
0x34 CPU post-memory initialization. Application Processor(s) (AP) initialization
0x35 CPU post-memory initialization. Boot Strap Processor (BSP) selection
0x36 CPU post-memory initialization. System Management Mode (SMM)
initialization
43
0x37 Post-Memory North Bridge initialization is started
0x38 Post-Memory North Bridge initialization (North Bridge module specific)
0x39 Post-Memory North Bridge initialization (North Bridge module specific)
0x3A Post-Memory North Bridge initialization (North Bridge module specific)
0x3B Post-Memory South Bridge initialization is started
0x3C Post-Memory South Bridge initialization (South Bridge module specific)
0x3D Post-Memory South Bridge initialization (South Bridge module specific)
0x3E Post-Memory South Bridge initialization (South Bridge module specific)
0x3F-0x4E OEM post memory initialization codes
0x4F DXE IPL is started
0x50 Memory initialization error. Invalid memory type or incompatible memory
speed
0x51 Memory initialization error. SPD reading has failed
0x52 Memory initialization error. Invalid memory size or memory modules do not
match
0x53 Memory initialization error. No usable memory detected
0x54 Unspecified memory initialization error
0x55 Memory not installed
0x56 Invalid CPU type or Speed
0x57 CPU mismatch
0x58 CPU self test failed or possible CPU cache error
0x59 CPU micro-code is not found or micro-code update is failed
0x5A Internal CPU error
0x5B reset PPI is not available
0x5C-0x5F Reserved for future AMI error codes
0xE0 S3 Resume is stared (S3 Resume PPI is called by the DXE IPL)
0xE1 S3 Boot Script execution
0xE2 Video repost
0xE3 OS S3 wake vector call
0xE4-0xE7 Reserved for future AMI progress codes
0xE8 S3 Resume Failed
0xE9 S3 Resume PPI not Found
0xEA S3 Resume Boot Script Error
0xEB S3 OS Wake Error
0xEC-0xEF Reserved for future AMI error codes
0xF0 Recovery condition triggered by firmware (Auto recovery)
0xF1 Recovery condition triggered by user (Forced recovery)
0xF2 Recovery process started
0xF3 Recovery firmware image is found
0xF4 Recovery firmware image is loaded
0xF5-0xF7 Reserved for future AMI progress codes
0xF8 Recovery PPI is not available
0xF9 Recovery capsule is not found
0xFA Invalid recovery capsule
0xFB – 0xFF Reserved for future AMI error codes
0x60 DXE Core is started
0x61 NVRAM initialization
44
0x62 Installation of the South Bridge Runtime Services
0x63 CPU DXE initialization is started
0x64 CPU DXE initialization (CPU module specific)
0x65 CPU DXE initialization (CPU module specific)
0x66 CPU DXE initialization (CPU module specific)
0x67 CPU DXE initialization (CPU module specific)
0x68 PCI host bridge initialization
0x69 North Bridge DXE initialization is started
0x6A North Bridge DXE SMM initialization is started
0x6B North Bridge DXE initialization (North Bridge module specific)
0x6C North Bridge DXE initialization (North Bridge module specific)
0x6D North Bridge DXE initialization (North Bridge module specific)
0x6E North Bridge DXE initialization (North Bridge module specific)
0x6F North Bridge DXE initialization (North Bridge module specific)
0x70 South Bridge DXE initialization is started
0x71 South Bridge DXE SMM initialization is started
0x72 South Bridge devices initialization
0x73 South Bridge DXE Initialization (South Bridge module specific)
0x74 South Bridge DXE Initialization (South Bridge module specific)
0x75 South Bridge DXE Initialization (South Bridge module specific)
0x76 South Bridge DXE Initialization (South Bridge module specific)
0x77 South Bridge DXE Initialization (South Bridge module specific)
0x78 ACPI module initialization
0x79 CSM initialization
0x7A – 0x7F Reserved for future AMI DXE codes
0x80 – 0x8F OEM DXE initialization codes
0x90 Boot Device Selection (BDS) phase is started
0x91 Driver connecting is started
0x92 PCI Bus initialization is started
0x93 PCI Bus Hot Plug Controller Initialization
0x94 PCI Bus Enumeration
0x95 PCI Bus Request Resources
0x96 PCI Bus Assign Resources
0x97 Console Output devices connect
0x98 Console input devices connect
0x99 Super IO Initialization
0x9A USB initialization is started
0x9B USB Reset
0x9C USB Detect
0x9D USB Enable
0x9E – 0x9F Reserved for future AMI codes
0xA0 IDE initialization is started
0xA1 IDE Reset
0xA2 IDE Detect
0xA3 IDE Enable
0xA4 SCSI initialization is started
0xA5 SCSI Reset
45
0xA6 SCSI Detect
0xA7 SCSI Enable
0xA8 Setup Verifying Password
0xA9 Start of Setup
0xAA Reserved for ASL (see ASL Status Codes section below)
0xAB Setup Input Wait
0xAC Reserved for ASL (see ASL Status Codes section below)
0xAD Ready To Boot event
0xAE Legacy Boot event
0xAF Exit Boot Services event
0xB0 Runtime Set Virtual Address MAP Begin
0xB1 Runtime Set Virtual Address MAP End
0xB2 Legacy Option ROM Initialization
0xB3 System Reset
0xB4 USB hot plug
0xB5 PCI bus hot plug
0xB6 Clean-up of NVRAM
0xB7 Configuration Reset (reset of NVRAM settings)
0xB8 – 0xBF Reserved for future AMI codes
0xC0 – 0xCF OEM BDS initialization codes
0xD0 CPU initialization error
0xD1 North Bridge initialization error
0xD2 South Bridge initialization error
0xD3 Some of the Architectural Protocols are not available
0xD4 PCI resource allocation error. Out of Resources
0xD5 No Space for Legacy Option ROM
0xD6 No Console Output Devices are found
0xD7 No Console Input Devices are found
0xD8 Invalid password
0xD9 Error loading Boot Option (LoadImage returned error)
0xDA Boot Option is failed (StartImage returned error)
0xDB Flash update is failed
0xDC Reset protocol is not available

4. 华擎P4VM900主板（集成显卡的）点不亮,用诊断卡显示d5d4是哪里问题？如何排除故障

内存坏了吧，换个内存试试。

5. 华擎主板故障灯怎么看

红色灯。指示灯亮一般有两种情况，一是主板通电指示，一是故障如果开机正常，那么主板的红灯亮可以不用管，如果开机异常，最好的办法的通过主板检测卡可以快速找到故障代码解决，单纯通过指示灯无法判断问题。主板电路问题，对此要找专业人员维修；红色灯。指示灯亮一般有两种情况，一是主板通电指示，一是故障。如果开机正常，那么主板的红灯亮可以不用管，如果开机异常，最好的办法的通过主板检测卡可以快速找到故障代码解决，单纯通过指示灯无法判断问题。主板电路问题，对此要找专业人员维修；

6. 华擎主板开机出现一串数字和英文，然后开不了机，求大神帮帮忙

系统没有找到硬盘。可能是硬盘没有插好，也有可能是硬盘坏。可以在关机状态下重新插接一下硬盘，若是硬盘接触的问题，可能就解决了。再不行，就是硬盘的问题了，可以把硬盘取下，挂到其它计算机上，若仍读不出硬盘，则硬盘坏。

7. 华擎主板重装系统后显示主板界面

您好，方法一

1、开机或重启电脑之后，当电脑第一屏幕信息出现时，根据屏幕下方的信息提示，如“Press DEl Enter Bios”、“Press F1 to Run Setup”之类信息时，按相应的键进入BIOS程序界面。
2、在BIOS界面中，将光标移动到“Load Optimized Default”项，并按回车键，
3、然后在弹出的窗口中选择“OK”并按回车键来实现恢复出厂设置。

方法二

1、开机不停按Delete键(笔记本一般是F2键)进入BIOS设置界面。

2、选择“Exit”菜单下面的“Load Setup Defaults”并回车，选择“Yes”之后，再次回车。

3、按“F10”键，选择“Yes”之后回车，此时系统会重启，BIOS主板成功恢复出厂设置。

8. 华擎主板内存电压偏低故障

华擎主板内存电压偏低故障解决方法如下：1、还原默认设置（防止人为将内存电压调低）。2、电脑能正常使用，就说明是主板内存有问题，建议更新主板内存。3、电脑不能正常使用，考虑电源供电不足，检查电源功率及是否损坏.